# Water quality in Harbor Isle, NY (Nassau County)

- Water source: Private wells
- Supplier / district: Liberty New York Water - Lynbrook Operations District
- Supplier contact: Liberty New York Water - Lynbrook Operations District (https://new-york-water.libertyutilities.com/uploads/Lynbrook_CCR.pdf)
- Report year: 2025 · Verified: 2026-11-11
- Web page: https://www.fieldstonewater.com/water/harbor-isle
- JSON: https://www.fieldstonewater.com/api/v1/towns/harbor-isle

Where the report prints both an average and a range, the status column here is judged on the average; where it prints a maximum or a 90th-percentile result, that figure is used. The report carries 2 notices: IMPORTANT INFORMATION ABOUT YOUR DRINKING WATER - Liberty New York Water-Lynbrook Operations Failure to Meet Treatment Requirements: silica levels (water quality parameters for lead and copper corrosion control) were outside the required ranges for more than nine days during two six-month monitoring periods (1/1/2025 to 6/30/2025 and 7/1/2025 to 12/31/2025) at both the point of entry and the distribution system, which constitutes two violations. Not an emergency; no action required. LNYW is working with NCDOH to establish updated ranges; states it has never exceeded the lead and copper 90th percentile action limits. State Water System ID#: 2902835. DRINKING WATER NOTICE - Monitoring Requirements Not Met for Liberty New York Water: during the 6-month monitoring period 1/1/2025-6/30/2025 LNYW did not complete all monitoring for Water Quality Parameters (WQP: pH, chlorine residual, silica, calcium, alkalinity). Table: Contaminant WQP; Required sampling frequency 6 Months; Number of samples taken 0; Number of Samples Required 8; When samples should have been taken 3/6/2025 - 3/20/2025; When samples were taken 3/26/2025. Samples were collected slightly outside the 14-day biweekly window; corrective measures implemented. State Water System ID#:2902835. None of Harbor Isle's land lies inside a mapped public water service area, per the NYS Department of Health boundaries EPA publishes; homes here are on private wells.

## Summary

Reported above a limit: PFOA, Iron.
Individual samples above the limit: Copper (high 3.6 vs limit 1.3 mg/L); Lead (high 261 vs limit 15 µg/L); Copper (high 2.4 vs limit 1.3 mg/L); Lead (high 387 vs limit 15 µg/L).
Detected: Free Chlorine, Total Trihalomethanes, Copper, Lead, Copper, Lead, Combined Radium 226/228, Gross beta, Uranium, Gross alpha, Barium, Copper, Lead, Arsenic, Chloride, Sulfate, Turbidity, Zinc, Nitrate, 1,4-Dioxane, PFOS, MTBE, Chlorodifluoromethane, Tetrachloroethene (PCE), Sodium, Manganese, Color, Odor, Nickel, Alkalinity, Calcium hardness, Calcium, Corrosivity (LSI), Hardness (total), Magnesium, pH, Total Dissolved Solids, Dacthal (DCPA), Perchlorate, Silver, PFBA, PFHxS, PFHxA, PFPeA, PFHpA, PFNA.

## Contaminants

| Contaminant | Average | Range | Unit | Limit | Limit source | Status | Peak above limit | Samples |
|---|---|---|---|---|---|---|---|---|
| Free Chlorine | 1.01 | 0.37 to 1.81 | mg/L | 4 | EPA MRDL | detected | no | — |
| Total Trihalomethanes | 4.75 | 2.7 to 5.9 | µg/L | 80 | EPA MCL | detected | no | — |
| Copper | 0.18 | 0.004 to 3.6 | mg/L | 1.3 | EPA action level | detected | yes | — |
| Lead | 4 | ND to 261 | µg/L | 15 | EPA action level | detected | yes | — |
| Copper | 0.21 | 0.001 to 2.4 | mg/L | 1.3 | EPA action level | detected | yes | — |
| Lead | 3 | ND to 387 | µg/L | 15 | EPA action level | detected | yes | — |
| Combined Radium 226/228 | — | ND to 3.36 | pCi/L | 5 | EPA MCL | detected | no | — |
| Gross beta | — | ND to 2.78 | pCi/L | 50 | EPA MCL | detected | no | — |
| Uranium | — | ND to 0.23 | µg/L | 30 | EPA MCL | detected | no | — |
| Gross alpha | — | ND to 3.74 | pCi/L | 15 | EPA MCL | detected | no | — |
| Barium | — | 0.002 to 0.11 | mg/L | 2 | EPA MCL | detected | no | — |
| Copper | — | ND to 0.29 | mg/L | 1.3 | EPA action level | detected | no | — |
| Lead | — | ND to 2.6 | µg/L | 15 | EPA action level | detected | no | — |
| Arsenic | — | ND to 4.9 | µg/L | 10 | EPA MCL | detected | no | — |
| Chloride | — | 9.0 to 52.4 | mg/L | 250 | NYS secondary standard | detected | no | — |
| Sulfate | — | 7.6 to 51.3 | mg/L | 250 | NYS secondary standard | detected | no | — |
| Turbidity | — | ND to 3.3 | NTU | 5 | EPA MCL | detected | no | — |
| Zinc | — | ND to 0.14 | mg/L | 5 | NYS secondary standard | detected | no | — |
| Nitrate | — | ND to 0.15 | mg/L | 10 | EPA MCL | detected | no | — |
| 1,4-Dioxane | — | ND to 0.18 | µg/L | 1 | NYS MCL | detected | no | — |
| PFOA | — | ND to 11.5 | ng/L | 10 | NYS MCL | exceeds | yes | — |
| PFOS | — | ND to 3.0 | ng/L | 10 | NYS MCL | detected | no | — |
| MTBE | — | ND to 3.1 | µg/L | 10 | EPA MCL | detected | no | — |
| Chlorodifluoromethane | — | ND to 0.61 | µg/L | 5 | EPA MCL | detected | no | — |
| Tetrachloroethene (PCE) | — | ND to 0.69 | µg/L | 5 | EPA MCL | detected | no | — |
| Sodium | — | 6.4 to 71.1 | mg/L | — | NYS guidance (20 mg/L for sodium-restricted diets) | detected | no | — |
| Iron | — | ND to 3.6 | mg/L | 0.3 | NYS secondary standard | exceeds | yes | — |
| Manganese | — | ND to 0.30 | mg/L | 0.3 | NYS secondary standard | detected | no | — |
| Color | — | ND to 5 | Units | 15 | NYS secondary standard | detected | no | — |
| Odor | — | ND to 2 | Units | 3 | NYS secondary standard | detected | no | — |
| Nickel | — | ND to 0.046 | mg/L | — | No regulatory limit | detected | no | — |
| Alkalinity | — | ND to 114 | mg/L | — | No regulatory limit | detected | no | — |
| Calcium hardness | — | 2.0 to 34.5 | mg/L | — | No regulatory limit | detected | no | — |
| Calcium | — | 0.82 to 13.8 | mg/L | — | No regulatory limit | detected | no | — |
| Corrosivity (LSI) | — | -6.28 to -0.19 | LSI | — | No regulatory limit | detected | no | — |
| Hardness (total) | — | 4.2 to 58.6 | mg/L | — | No regulatory limit | detected | no | — |
| Magnesium | — | 0.54 to 7.4 | mg/L | — | No regulatory limit | detected | no | — |
| pH | — | 3.7 to 8.9 | Units | — | NYS guidance range 7.5–8.5 | detected | no | — |
| Total Dissolved Solids | — | ND to 229 | mg/L | — | No regulatory limit | detected | no | — |
| Dacthal (DCPA) | — | ND to 1.8 | µg/L | 50 | NYS notification level | detected | no | — |
| Perchlorate | — | ND to 1.2 | µg/L | 18.0 | NYS notification level | detected | no | — |
| Silver | — | ND to 38 | µg/L | 100 | NYS notification level | detected | no | — |
| PFBA | — | ND to 4.6 | ng/L | — | No regulatory limit | detected | no | — |
| PFHxS | — | ND to 7.0 | ng/L | — | No regulatory limit | detected | no | — |
| PFHxA | — | ND to 6.6 | ng/L | — | No regulatory limit | detected | no | — |
| PFPeA | — | ND to 6.9 | ng/L | — | No regulatory limit | detected | no | — |
| PFHpA | — | ND to 4.4 | ng/L | — | No regulatory limit | detected | no | — |
| PFNA | — | ND to 0.0041 | µg/L | — | EPA MCL of 0.010 µg/L takes effect 2029; no limit in force | detected | no | 35 |
| PFBS | — | ND to ND | µg/L | — | No regulatory limit | not-detected | no | 35 |
| HFPO-DA | — | ND to ND | µg/L | — | EPA MCL of 0.010 µg/L takes effect 2029; no limit in force | not-detected | no | 35 |

## Sources

- Liberty New York Water - Lynbrook Operations District 2025 Annual Water Quality Report: https://new-york-water.libertyutilities.com/uploads/Lynbrook_CCR.pdf
- EPA UCMR 5 PFAS results, 2023–2025 (entry-point samples): https://www.epa.gov/dwucmr/occurrence-data-unregulated-contaminant-monitoring-rule

## Notes on this data

- Public-water figures are annual results published by the water supplier in its Annual Drinking Water Quality Report (CCR), reported across all wells feeding a distribution area. They describe water leaving the supplier, not the tap in a specific home.
- Private wells are not covered by any public report. Well owners need their own test.
- Status compares the reported average (or the range high where no average is published) to the regulatory limit. 'exceeds' is a numeric comparison, not a regulatory violation finding; see violationFlag for what the supplier reported.
- epaSystems lists the public water systems that report serving this community's ZIP codes (EPA UCMR 5 ZIP list) with their EPA SDWIS violation counts. Counts are compliance events, not contaminant levels.
- publicWaterCoverage: share (0-1) of the community's land inside a public water system service area, from the NYS DOH boundaries EPA publishes; >=0.9 is shown as public water, <=0.1 as private wells, between as mixed.
- areaAssignment: 'inferred' means the SCWA distribution area was taken from neighboring mapped communities, not read from SCWA's map; confirm with SCWA's address lookup.
- dataTier: 'report' = rows from the supplier's annual water quality report; 'epa' = EPA-reported lead and PFAS sampling results so far; 'none' = no public supplier mapped (private wells).
- peakAboveLimit marks a contaminant whose highest single sample was above the limit even though its average was not. Compliance is judged on averages; peaks show what some homes may have received at times.
- Units: µg/L = micrograms per liter = parts per billion; mg/L = milligrams per liter = parts per million. ND = not detected.

## What this means for treatment

For Harbor Isle, the numbers point first to under-sink reverse osmosis, whole-house carbon filtration, and private well treatment: dissolved contaminants close to their limits.

- **Under-Sink Reverse Osmosis** (recommended): Dissolved contaminants close to their limits. PFOA/PFOS reached 11.5 ng/L (ppt) in at least one sample — above New York's 10 ppt limit and at or above the 4.0 ppt federal MCL, with federal compliance due April 26, 2029. Whether an under-sink reverse osmosis model reduces PFOA or PFOS depends on that model's certification or performance data sheet. Sodium averaged 71.1 mg/L, above the 20 mg/L level New York flags for sodium-restricted diets. Perchlorate was detected up to 1.2 µg/L (limit 18). The supplier's 90th-percentile lead result was 0.004 mg/L (4 ppb) against the 15 ppb action level. Lead enters water from a home's own service line and fixtures, so the system figure says little about any one house; a filter certified for lead (NSF/ANSI 53) or reverse osmosis at the kitchen tap reduces it at the point you drink.
- **Whole-House Carbon Filtration** (recommended): Solvent traces and chlorine in the supply. Free chlorine averaged 1.01 mg/L at the entry point (limit 4), the residual that gives tap water its pool taste and dries skin and hair. Solvent traces were detected: Tetrachloroethene (PCE) up to 0.69 µg/L (limit 5 each). Whether a whole-house carbon model reduces those solvents is on that model's data sheet.
- **Private Well Treatment** (recommended): Private wells in part of the community. Part of Harbor Isle is on private wells that none of these figures cover; a well needs its own test, and a well package is sized to what it finds.
- **Whole-House + Softener Combo** (not needed): Hardness 58.6 mg/L, about 3.4 grains per gallon. At 58.6 mg/L (3.4 gpg) the water is soft. A softener is not needed.

## Test your own water

A utility report describes the supply, not your tap, and does not cover private wells. Fieldstone Water Co. offers a free in-home water test across Long Island: call 516-43WATER (516-439-2837) or book at https://www.fieldstonewater.com/free-water-test.

---
Compilation © Fieldstone Water Co., licensed CC BY 4.0 (the underlying public records are not ours to copyright): reuse with attribution and a link to https://www.fieldstonewater.com/water/harbor-isle, keeping each figure's source citation. Text and explainers all rights reserved. https://www.fieldstonewater.com/terms#data-license
