# Water quality in Sands Point, NY (Nassau County)

- Water source: Public water, some private wells
- Supplier / district: Inc. Village of Sands Point (Sands Point Water Department)
- Supplier contact: Inc. Village of Sands Point (Sands Point Water Department) (https://www.sandspoint.gov/post/annual-drinking-water-quality-report-for-2025)
- Report year: 2025 · Verified: 2026-11-11
- Web page: https://www.fieldstonewater.com/water/sands-point
- JSON: https://www.fieldstonewater.com/api/v1/towns/sands-point

Where the report prints both an average and a range, the status column here is judged on the average; where it prints a maximum or a 90th-percentile result, that figure is used. The report carries 3 notices: Table 1 PFOA row prints Violation 'Yes' (Maximum 11.0 ng/l on 03/18/25 against *MCL=10, NY State MCL); Likely Source cell begins 'Well was offline for when high was detected.' On September 18, 2025. NCDH observed a pH of 5.89 from an analyzer inside pumpstation of Well 3 N 43898 due to a caustic soda injection leak and issued the Village a Violation for change in treatment process without notification to the NCDH. At the time of incident Well 4 with fully functioning treatment was in lead and well 3 was set to last on first off position. The well ran during peak irrigation hours. Both wells running together and mixing in system distribution while leaving the facility, (although pH readings were lower than normal when analyzed by handheld devices), were still receiving pH adjustment. At a distribution sample tap on site, not the continuous analyzer, the lowest observed pH was a 6.9. Although the system not being designed to operate this way the mixing of the two wells did produce treated water albeit above the targeted pH. Being that the system was not designed this way it was not found acceptable by the NCDH. Page 5 (Nitrate): 'As you can see by the table, our system had no violations, but we have learned through our testing that some contaminants have been detected; however, these contaminants were detected below New York State requirements. Although nitrate was detected below the MCL, it was detected at 0.05-6.6 which is greater than one-half of the MCL. Therefore, we are required to present the following information on nitrate in drinking water...' (mandatory nitrate health-effects language follows). About 40% of Sands Point's land lies inside a public water service area (Sands Point (Village)), per the NYS Department of Health boundaries EPA publishes; the rest is on private wells. These results apply only to public water.

## Summary

No contaminant averaged above its limit in the reported year.
Individual samples above the limit: Iron (high 0.36 vs limit 0.30 mg/L); PFOA (high 11.0 vs limit 10 ng/L).
Detected: Chloride, Nitrate, Sulfate, Sodium, Manganese, Magnesium, Calcium, Iron, Barium, Nickel, Nitrate-Nitrite (as N), Copper, Lead, Total Trihalomethanes, Turbidity, Chloroform, Gross beta, Radium-228, Combined Radium 226/228, Uranium, 1,4-Dioxane, PFOA, PFOS, DCPA mono and di-acids, Calcium hardness, Hardness (total), Alkalinity, Total Dissolved Solids, pH, Free Chlorine, Color, Odor, PFHxS, PFBA, PFHxA, PFPeA, PFHpA, PFBS.

## Contaminants

| Contaminant | Average | Range | Unit | Limit | Limit source | Status | Peak above limit | Samples |
|---|---|---|---|---|---|---|---|---|
| Chloride | 26.27 | 11.1 to 56.8 | mg/L | 250 | NYS secondary standard | detected | no | — |
| Nitrate | 3.90 | <0.050 to 4.70 | mg/L | 10 | EPA MCL | detected | no | — |
| Sulfate | 31.12 | 13.1 to 43.8 | mg/L | 250 | NYS secondary standard | detected | no | — |
| Sodium | 19.34 | 6.4 to 33.9 | mg/L | — | NYS guidance (20 mg/L for sodium-restricted diets) | detected | no | — |
| Manganese | 0.27 | <0.010 to 0.047 | mg/L | 0.30 | NYS secondary standard | detected | no | — |
| Magnesium | 11.64 | 6.1 to 17.4 | mg/L | — | No regulatory limit | detected | no | — |
| Calcium | 24.04 | 15.0 to 30.4 | mg/L | — | No regulatory limit | detected | no | — |
| Iron | 0.049 | <0.020 to 0.36 | mg/L | 0.30 | NYS secondary standard | detected | yes | — |
| Barium | 0.033 | 0.02 to 0.042 | mg/L | 2 | EPA MCL | detected | no | — |
| Nickel | 0.0038 | <0.00050 to 0.0075 | mg/L | — | No regulatory limit | detected | no | — |
| Nitrate-Nitrite (as N) | 3.91 | <0.050 to 4.7 | mg/L | — | No regulatory limit | detected | no | — |
| Copper | 0.24 | <0.054 to 0.36 | mg/L | 1.3 | EPA action level | detected | no | — |
| Lead | 2.1 | <1.0 to 2.6 | µg/L | 15 | EPA action level | detected | no | — |
| Total Trihalomethanes | <2.0 | N/A to N/A | µg/L | — | No regulatory limit | detected | no | — |
| Turbidity | 3.71 | < 1.0 to 65.0 | NTU | — | No regulatory limit | detected | no | — |
| Chloroform | 1.04 | <0.50 to 2.30 | µg/L | 50 | EPA MCL | detected | no | — |
| Gross beta | 1.72 | 1.13 to 2.81 | pCi/L | 50 | EPA MCL | detected | no | — |
| Radium-228 | 0.56 | 0.0856 to 1.21 | pCi/L | — | No regulatory limit | detected | no | — |
| Combined Radium 226/228 | 1.21 | N/A to N/A | pCi/L | — | No regulatory limit | detected | no | — |
| Uranium | 1.31 | N/A to N/A | pCi/L | — | No regulatory limit | detected | no | — |
| 1,4-Dioxane | 0.032 | <0.020 to 0.044 | µg/L | 1 | NYS MCL | detected | no | — |
| PFOA | 3.41 | <2.2 to 11.0 | ng/L | 10 | NYS MCL | detected | yes | — |
| PFOS | 1.29 | <1.9 to 4.30 | ng/L | 10 | NYS MCL | detected | no | — |
| DCPA mono and di-acids | 2.84 | <.10 to 1.8 | µg/L | 50 | EPA MCL | detected | no | — |
| Calcium hardness | 24.11 | 15.0 to 75.9 | mg/L | — | No regulatory limit | detected | no | — |
| Hardness (total) | 108.86 | 65.9 to 136 | mg/L | — | No regulatory limit | detected | no | — |
| Alkalinity | 67.91 | 46.8 to 72.1 | mg/L | — | No regulatory limit | detected | no | — |
| Total Dissolved Solids | 190.45 | 105 to 247 | mg/L | — | No regulatory limit | detected | no | — |
| pH | 7.2 | 7.0 to 7.2 | Std Units | — | NYS guidance range 7.5–8.5 | detected | no | — |
| Free Chlorine | 0.9 | 0.5 to 1.50 | mg/L | 4.0 | EPA MRDL | detected | no | — |
| Color | 5 units | — | — | — | No regulatory limit | detected | no | — |
| Odor | 1 TON | — | — | — | No regulatory limit | detected | no | — |
| PFHxS | 0.92 | <1.8 to 1.9 | ng/L | — | No regulatory limit | detected | no | — |
| PFBA | 4.12 | <1.8 to 5.60 | ng/L | — | No regulatory limit | detected | no | — |
| PFHxA | 2.77 | 2.3 to 3.30 | ng/L | — | No regulatory limit | detected | no | — |
| PFPeA | 3.60 | 2.7 to 4.6 | ng/L | — | No regulatory limit | detected | no | — |
| PFHpA | 2.07 | <1.8 to 3.20 | ng/L | — | No regulatory limit | detected | no | — |
| PFBS | 1.95 | <1.9 to 2.70 | ng/L | — | No regulatory limit | detected | no | — |

## Sources

- Inc. Village of Sands Point (Sands Point Water Department) 2025 Annual Water Quality Report: https://www.sandspoint.gov/post/annual-drinking-water-quality-report-for-2025

## EPA compliance record (suppliers serving this community's ZIP codes)

| System | EPA ID | Violations | Health-based | All time | Window | EPA report |
|---|---|---|---|---|---|---|
| Port Washington Water District | NY2912267 | 1 | 1 | 1 | 2022–2026 | https://echo.epa.gov/detailed-facility-report?fid=NY2912267 |

## Notes on this data

- Public-water figures are annual results published by the water supplier in its Annual Drinking Water Quality Report (CCR), reported across all wells feeding a distribution area. They describe water leaving the supplier, not the tap in a specific home.
- Private wells are not covered by any public report. Well owners need their own test.
- Status compares the reported average (or the range high where no average is published) to the regulatory limit. 'exceeds' is a numeric comparison, not a regulatory violation finding; see violationFlag for what the supplier reported.
- epaSystems lists the public water systems that report serving this community's ZIP codes (EPA UCMR 5 ZIP list) with their EPA SDWIS violation counts. Counts are compliance events, not contaminant levels.
- publicWaterCoverage: share (0-1) of the community's land inside a public water system service area, from the NYS DOH boundaries EPA publishes; >=0.9 is shown as public water, <=0.1 as private wells, between as mixed.
- areaAssignment: 'inferred' means the SCWA distribution area was taken from neighboring mapped communities, not read from SCWA's map; confirm with SCWA's address lookup.
- dataTier: 'report' = rows from the supplier's annual water quality report; 'epa' = EPA-reported lead and PFAS sampling results so far; 'none' = no public supplier mapped (private wells).
- peakAboveLimit marks a contaminant whose highest single sample was above the limit even though its average was not. Compliance is judged on averages; peaks show what some homes may have received at times.
- Units: µg/L = micrograms per liter = parts per billion; mg/L = milligrams per liter = parts per million. ND = not detected.

## What this means for treatment

For Sands Point, the numbers point first to under-sink reverse osmosis and whole-house carbon filtration: dissolved contaminants close to their limits.

- **Under-Sink Reverse Osmosis** (recommended): Dissolved contaminants close to their limits. Nitrate averaged 3.9 mg/L (limit 10), moderate but present; reverse osmosis reduces it at the tap. PFOA/PFOS reached 11 ng/L (ppt) in at least one sample — above New York's 10 ppt limit and at or above the 4.0 ppt federal MCL, with federal compliance due April 26, 2029. Whether an under-sink reverse osmosis model reduces PFOA or PFOS depends on that model's certification or performance data sheet. The supplier's 90th-percentile lead result was 0.0021 mg/L (2 ppb) against the 15 ppb action level. Lead enters water from a home's own service line and fixtures, so the system figure says little about any one house; a filter certified for lead (NSF/ANSI 53) or reverse osmosis at the kitchen tap reduces it at the point you drink.
- **Whole-House Carbon Filtration** (recommended): Chlorine residual 0.9 mg/L. Free chlorine averaged 0.9 mg/L at the entry point (limit 4), the residual that gives tap water its pool taste and dries skin and hair. Chlorination by-products (trihalomethanes) reached 2.3 µg/L in some samples against an 80 µg/L limit for the group; they are absorbed in the shower as well as drunk.
- **Whole-House + Softener Combo** (worth considering): Hardness 109 mg/L, about 6.4 grains per gallon. At 109 mg/L (6.4 gpg) the water is moderately hard. A softener is a comfort choice here, not a necessity; some homes near the top of the 136 mg/L range will notice scale.
- **Private Well Treatment** (worth considering): Private wells in part of the community. Part of Sands Point is on private wells that none of these figures cover; a well needs its own test, and a well package is sized to what it finds.

## Test your own water

A utility report describes the supply, not your tap, and does not cover private wells. Fieldstone Water Co. offers a free in-home water test across Long Island: call 516-43WATER (516-439-2837) or book at https://www.fieldstonewater.com/free-water-test.

---
Compilation © Fieldstone Water Co., licensed CC BY 4.0 (the underlying public records are not ours to copyright): reuse with attribution and a link to https://www.fieldstonewater.com/water/sands-point, keeping each figure's source citation. Text and explainers all rights reserved. https://www.fieldstonewater.com/terms#data-license
